NXP S32Z/E Pin Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nxp,s32ze-pinctrl
.. _dtbinding_nxp_s32ze_pinctrl:

nxp,s32ze-pinctrl
#################

Vendor: :ref:`NXP Semiconductors <dt_vendor_nxp>`

Description
***********



.. code-block:: none

   NXP S32 pinctrl node for S32Z/E SoCs.

   The NXP S32 pin controller is a singleton node responsible for controlling
   the pin function selection and pin properties. This node, labeled 'pinctrl' in
   the SoC's devicetree, will define pin configurations in pin groups. Each group
   within the pin configuration defines the pin configuration for a peripheral,
   and each numbered subgroup in the pin group defines all the pins for that
   peripheral with the same configuration properties. The 'pinmux' property in
   a group selects the pins to be configured, and the remaining properties set
   configuration values for those pins.

   For example, to configure the pinmux for UART0, modify the 'pinctrl' from your
   board or application devicetree overlay as follows:

     /* Include the SoC package header containing the predefined pins definitions */
     #include <nxp/s32/S32Z27-BGA594-pinctrl.h>

     &pinctrl {
       uart0_default: uart0_default {
         group1 {
           pinmux = <PB10_LIN_0_TX>;
           output-enable;
         };
         group2 {
           pinmux = <PB11_LIN_0_RX>;
           input-enable;
         };
       };
     };

   The 'uart0_default' node contains the pin configurations for a particular state
   of a device. The 'default' state is the active state. Other states for the same
   device can be specified in separate child nodes of 'pinctrl'.

   In addition to 'pinmux' property, each group can contain other properties such as
   'bias-pull-up' or 'slew-rate' that will be applied to all the pins defined in
   'pinmux' array. To enable the input buffer use 'input-enable' and to enable the
   output buffer use 'output-enable'.

   To link the pin configurations with UART0 device, use pinctrl-N property in the
   device node, where 'N' is the zero-based state index (0 is the default state).
   Following previous example:

     &uart0 {
       pinctrl-0 = <&uart0_default>;
       pinctrl-names = "default";
       status = "okay";
     };

   If only the required properties are supplied, the pin configuration register
   will be assigned the following reset values:
     - input and output buffers disabled
     - internal pull not enabled
     - open drain disabled
     - slew rate 4 (see description in property below).

   Additionally, Safe Mode is always disabled (reset value) and configuration that
   only applies to LVDS pads, which are not supported, default to reset values:
     - termination resistor disabled
     - receiver single ended
     - current reference control disabled
     - Rx current boost disabled.

Properties
**********

Top level properties
====================


These property descriptions apply to "nxp,s32ze-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nxp,s32ze-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Grandchild node properties
==========================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``input-enable``
     - ``boolean``
     - .. code-block:: none

          enable input on pin (e.g. enable an input buffer, no effect on output)



   * - ``output-enable``
     - ``boolean``
     - .. code-block:: none

          enable output on a pin without actively driving it (e.g. enable an output
          buffer)



   * - ``slew-rate``
     - ``int``
     - .. code-block:: none

          Slew rate control. Reset value is 4.
          - For 3.3 V / 1.8 V FAST pads:
            0: FMAX_3318 = 208 MHz (at 1.8 V), 166 MHz (at 3.3 V)
            4: FMAX_3318 = 166 MHz (at 1.8 V), 150 MHz (at 3.3 V)
            5: FMAX_3318 = 150 MHz (at 1.8 V), 133 MHz (at 3.3 V)
            6: FMAX_3318 = 133 MHz (at 1.8 V), 100 MHz (at 3.3 V)
            7: FMAX_3318 = 100 MHz (at 1.8 V), 83 MHz (at 3.3 V)
          - For 1.8 V GPIO pads:
            0: FMAX_18 = 208 MHz
            4: FMAX_18 = 150 MHz
            5: FMAX_18 = 133 MHz
            6: FMAX_18 = 100 MHz
            7: FMAX_18 = 50 MHz
          - For 3.3 V GPIO pads:
            0: Reserved
            4: FMAX_33 = 50 MHz
            5: FMAX_33 = 50 MHz
            6: FMAX_33 = 50 MHz
            7: FMAX_33 = 1 MHz



       Default value: ``4``

       Legal values: ``0``, ``4``, ``5``, ``6``, ``7``

   * - ``pinmux``
     - ``array``
     - .. code-block:: none

          An array of pins sharing the same group properties. The pins must be
          defined using the macros from the SoC package header. These macros
          encode all the pin muxing information in a 32-bit value.



       This property is **required**.