NXP LPC11U6x Pin Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nxp,lpc11u6x-pinctrl
.. _dtbinding_nxp_lpc11u6x_pinctrl:

nxp,lpc11u6x-pinctrl
####################

Vendor: :ref:`NXP Semiconductors <dt_vendor_nxp>`

Description
***********



.. code-block:: none

   LPC pinctrl node. This node defines pin configurations in pin groups, and has
   the 'pinctrl' node identifier in the SOC's devicetree. Each group within the
   pin configuration defines a peripheral's pin configuration. Each numbered
   subgroup represents pins with shared configuration for that peripheral. The
   'pinmux' property of each group selects the pins to be configured with these
   properties. For example, here is a configuration for FLEXCOMM0 pins:

   pinmux_flexcomm0_usart: pinmux_flexcomm0_usart {
     group0 {
       pinmux = <FC0_TXD_SCL_MISO_WS_PIO0_30>,
               <FC0_RXD_SDA_MOSI_DATA_PIO0_29>;
       slew-rate = "standard";
     };
   };

   If only the required properties are supplied, the ICON_PIO register will
   be assigned the following values:
   IOCON_FUNC=<pin mux selection>,
   IOCON_MODE=0,
   IOCON_SLEW=<slew-rate selection>,
   IOCON_INVERT=0,
   IOCON_DIGIMODE=1,
   IOCON_OD=0,

   Values for I2C type and analog type pins have the following defaults:
   IOCON_ASW=0
   IOCON_SSEL=0
   IOCON_FILTEROFF=1
   IOCON_ECS=0
   IOCON_EGP=1
   IOCON_I2CFILTER=1

   Note the inherited pinctrl properties defined below have the following effects:
   drive-open-drain: IOCON_OD=1
   bias-pull-up: IOCON_MODE=2
   bias-pull-down: IOCON_MODE=1
   drive-push-pull: IOCON_MODE=3

   Note: for the LPC11u6x, the following fields are also supported:
   IOCON_HYS- set by input-schmitt-enable
   IOCON_S_MODE- set by nxp,digital-filter
   IOCON_CLKDIV- set by nxp,filter-clock-div
   IOCON_FILTR- set by nxp,analog-filter

Properties
**********

Top level properties
====================


These property descriptions apply to "nxp,lpc11u6x-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nxp,lpc11u6x-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Grandchild node properties
==========================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-push-pull``
     - ``boolean``
     - .. code-block:: none

          drive actively high and low


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``input-schmitt-enable``
     - ``boolean``
     - .. code-block:: none

          enable schmitt-trigger mode


   * - ``nxp,digital-filter``
     - ``int``
     - .. code-block:: none

          Enable digital filter. Set number of clock cycles to use as rejection
          threshold for input pulses. 0 disables the filter. Only valid for
          lpc11u6x SOC. Filter defaults to disabled, as this is default reset
          value for SOC



       Legal values: ``0``, ``1``, ``2``, ``3``

   * - ``nxp,filter-clock-div``
     - ``int``
     - .. code-block:: none

          set peripheral clock divider for input filter sampling clock
          IOCONCLKDIV. Only valid for lpc11u6x SOC. Default to 0, as this
          is the default reset value for the SOC.



       Legal values: ``0``, ``1``, ``2``, ``3``, ``4``, ``5``, ``6``

   * - ``nxp,disable-analog-filter``
     - ``boolean``
     - .. code-block:: none

          Disable fixed 10 ns input glitch analog filter. Only valid for lpc11u6x
          SOC, on analog pins. Note that this filter is enabled on reset, hence
          the choice to make disabling the filter opt-in



   * - ``pinmux``
     - ``array``
     - .. code-block:: none

          Pin mux selection for this group. See the SOC level pinctrl header
          file in NXP's HAL for a defined list of these options.



       This property is **required**.

   * - ``nxp,invert``
     - ``boolean``
     - .. code-block:: none

          Invert the pin input logic level



   * - ``nxp,analog-mode``
     - ``boolean``
     - .. code-block:: none

          Set the pin to analog mode. Sets DIGIMODE=0, and ASW=1. Only valid for
          analog type pins. Selects ASW0 on LPC55s3x family



   * - ``nxp,i2c-filter``
     - ``string``
     - .. code-block:: none

          I2C glitch filter speed. Only valid for I2C mode pins. Fast mode
          typically only required for High speed I2C.



       Legal values: ``'slow'``, ``'fast'``

   * - ``nxp,i2c-mode``
     - ``boolean``
     - .. code-block:: none

          Enable I2C mode for a pin. If not present, pin is in GPIO mode. Only
          valid for I2C mode pins