CAP shell 사용법

Bluetooth: Common Audio Profile Shell
#####################################

This document describes how to run the Common Audio Profile functionality.

CAP Acceptor
************

The Acceptor will typically be a resource-constrained device, such as a headset, earbud or hearing
aid. The Acceptor can initialize a Coordinated Set Identification Service instance, if it is in
a pair with one or more other CAP Acceptors.

Using the CAP Acceptor
======================

When the Bluetooth stack has been initialized (:code:`bt init`), the Acceptor can be registered by
calling :code:`cap_acceptor init`, which will register the CAS and CSIS services, as well as
register callbacks.

.. code-block:: console


   cap_acceptor --help
   cap_acceptor - Bluetooth CAP acceptor shell commands
   Subcommands:
     init          :Initialize the service and register callbacks [size <int>]
                    [rank <int>] [not-lockable] [sirk <data>]
     lock          :Lock the set
     release       :Release the set [force]
     sirk          :Set the currently used SIRK <sirk>
     get_sirk      :Get the currently used SIRK
     sirk_rsp      :Set the response used in SIRK requests <accept, accept_enc,
                    reject, oob>

Besides initializing the CAS and the CSIS, there are also commands to lock and release the CSIS
instance, as well as printing and modifying access to the SIRK of the CSIS.

Setting a new SIRK
------------------

This command can modify the currently used SIRK. To get the new RSI to advertise on air,
:code:`bt adv-data` or :code:`bt advertise` must be called again to set the new advertising data.
If :code:`CONFIG_BT_CSIP_SET_MEMBER_NOTIFIABLE` is enabled, this will also notify connected
clients.

.. code-block:: console

   uart:~$ cap_acceptor sirk 00112233445566778899aabbccddeeff
   SIRK updated

Getting the current SIRK
------------------------

This command can get the currently used SIRK.

.. code-block:: console

   uart:~$ cap_acceptor get_sirk
   SIRK
   36 04 9a dc 66 3a a1 a1 |6...f:..
   1d 9a 2f 41 01 73 3e 01 |../A.s>.

CAP Initiator
*************

The Initiator will typically be a resource-rich device, such as a phone or PC. The Initiator can
discover CAP Acceptors's CAS and optional CSIS services. The CSIS service can be read to provide
information about other CAP Acceptors in the same Coordinated Set. The Initiator can execute
stream control procedures on sets of devices, either ad-hoc or Coordinated, and thus provides an
easy way to setup multiple streams on multiple devices at once.

Using the CAP Initiator
=======================

When the Bluetooth stack has been initialized (:code:`bt init`), the Initiator can discover CAS and
the optionally included CSIS instance by calling (:code:`cap_initiator discover`).
The CAP initiator also supports broadcast audio as a source.

.. code-block:: console

   uart:~$ cap_initiator --help
   cap_initiator - Bluetooth CAP initiator shell commands
   Subcommands:
     discover          : Discover CAS
     unicast_start     : Unicast Start [csip] [sinks <cnt> (default 1)] [sources
                        <cnt> (default 1)] [conns (<cnt> | all) (default 1)]
     unicast_list      : Unicast list streams
     unicast_update    : Unicast Update <all | stream [stream [stream...]]>
     unicast_stop      : Unicast stop streams [stream [stream [stream...]]] (all by default)
     unicast_cancel    : Unicast cancel current procedure
     ac_1              : Unicast audio configuration 1
     ac_2              : Unicast audio configuration 2
     ac_3              : Unicast audio configuration 3
     ac_4              : Unicast audio configuration 4
     ac_5              : Unicast audio configuration 5
     ac_6_i            : Unicast audio configuration 6(i)
     ac_6_ii           : Unicast audio configuration 6(ii)
     ac_7_i            : Unicast audio configuration 7(i)
     ac_7_ii           : Unicast audio configuration 7(ii)
     ac_8_i            : Unicast audio configuration 8(i)
     ac_8_ii           : Unicast audio configuration 8(ii)
     ac_9_i            : Unicast audio configuration 9(i)
     ac_9_ii           : Unicast audio configuration 9(ii)
     ac_10             : Unicast audio configuration 10
     ac_11_i           : Unicast audio configuration 11(i)
     ac_11_ii          : Unicast audio configuration 11(ii)
     broadcast_start   :
     broadcast_update  : <meta>
     broadcast_stop    :
     broadcast_delete  :
     ac_12             : Broadcast audio configuration 12
     ac_13             : Broadcast audio configuration 13
     ac_14             : Broadcast audio configuration 14

Before being able to perform any stream operation, the device must also perform the
:code:`bap discover` operation to discover the ASEs and PAC records. The :code:`bap init`
command also needs to be called.

When connected
--------------

Discovering CAS and CSIS on a device:

.. code-block:: console

   uart:~$ cap_initiator discover
   discovery completed with CSIS


Discovering ASEs and PAC records on a device:

.. code-block:: console

   uart:~$ bap discover
   conn 0x81cc260: #0: codec 0x81d5b28 dir 0x01
   codec 0x06 cid 0x0000 vid 0x0000 count 5
   data #0: type 0x01 len 2
   00000000: f5                                               |.                |
   data #1: type 0x02 len 1
   data #2: type 0x03 len 1
   data #3: type 0x04 len 4
   00000000: 1e 00 f0                                         |...              |
   data #4: type 0x05 len 1
   meta #0: type 0x01 len 2
   00000000: 06                                               |.                |
   dir 1 loc 1
   snk ctx 6 src ctx 6
   Conn: 0x81cc260, Sink #0: ep 0x81e4248
   Conn: 0x81cc260, Sink #1: ep 0x81e46a8
   conn 0x81cc260: #0: codec 0x81d5f00 dir 0x02
   codec 0x06 cid 0x0000 vid 0x0000 count 5
   data #0: type 0x01 len 2
   00000000: f5                                               |.                |
   data #1: type 0x02 len 1
   data #2: type 0x03 len 1
   data #3: type 0x04 len 4
   00000000: 1e 00 f0                                         |...              |
   data #4: type 0x05 len 1
   meta #0: type 0x01 len 2
   00000000: 06                                               |.                |
   dir 2 loc 1
   snk ctx 6 src ctx 6
   Conn: 0x81cc260, Source #0: ep 0x81e5c88
   Conn: 0x81cc260, Source #1: ep 0x81e60e8
   Discover complete: err 0

Both of the above commands should be done for each device that you want to use in the set.
To use multiple devices, simply connect to more and then use :code:`bt select` the device to execute
the commands on.

Once all devices have been connected and the respective discovery commands have been called, the
:code:`cap_initiator unicast_start` command can be used to put one or more streams into the
streaming state.

.. code-block:: console

   uart:~$ cap_initiator unicast_start sinks 1 sources 0 conns all
   Setting up 1 sinks and 0 sources on each (2) conn
   Starting 1 streams
   Unicast start completed

To stop all the streams that has been started, the :code:`cap_initiator unicast_stop` command can be
used.


.. code-block:: console

   uart:~$ cap_initiator unicast_stop all
   Unicast stop completed

When doing broadcast
--------------------

To start a broadcast as the CAP initiator there are a few steps to be done:

1. Create and configure an extended advertising set with periodic advertising
2. Create and configure a broadcast source
3. Setup extended and periodic advertising data

The following commands will setup a CAP broadcast source using the 16_2_1 preset (defined by BAP):


.. code-block:: console

   bt init
   bap init
   bt adv-create nconn-nscan ext-adv name
   bt per-adv-param
   bap preset broadcast 16_2_1
   cap_initiator ac_12
   bt adv-data discov
   bt per-adv-data
   cap_initiator broadcast_start


The broadcast source is created by the :code:`cap_initiator ac_12`, :code:`cap_initiator ac_13`,
and :code:`cap_initiator ac_14` commands, configuring the broadcast source for the defined audio
configurations from BAP. The broadcast source can then be stopped with
:code:`cap_initiator broadcast_stop` or deleted with :code:`cap_initiator broadcast_delete`.

The metadata of the broadcast source can be updated at any time, including when it is already
streaming. To update the metadata the :code:`cap_initiator broadcast_update` command can be used.
The command takes an array of data, and the only requirement (besides having valid data) is that the
streaming context shall be set. For example to set the streaming context to media, the command can
be used as

.. code-block:: console

   cap_initiator broadcast_update 03020400
   CAP Broadcast source updated with new metadata. Update the advertised base via `bt per-adv-data`
   bt per-adv-data

The :code:`bt per-adv-data` command should be used afterwards to update the data is the advertised
BASE. The data must be little-endian, so in the above example the metadata :code:`03020400` is
setting the metadata entry with :code:`03` as the length, :code:`02` as the type (streaming context)
and :code:`0400` as the value :code:`BT_AUDIO_CONTEXT_TYPE_MEDIA`
(which has the numeric value of 0x).

CAP Commander
*************

The Commander will typically be a either co-located with a CAP Initiator or be on a separate
resource-rich mobile device, such as a phone or smartwatch. The Commander can
discover CAP Acceptors's CAS and optional CSIS services. The CSIS service can be read to provide
information about other CAP Acceptors in the same Coordinated Set. The Commander can provide
information about broadcast sources to CAP Acceptors or coordinate capture and rendering information
such as mute or volume states.

Using the CAP Commander
=======================

When the Bluetooth stack has been initialized (:code:`bt init`), the Commander can discover CAS and
the optionally included CSIS instance by calling (:code:`cap_commander discover`).

.. code-block:: console

   cap_commander --help
   cap_commander - Bluetooth CAP commander shell commands
   Subcommands:
     discover                :Discover CAS
     cancel                  :CAP commander cancel current procedure
     change_volume           :Change volume on all connections <volume>
     change_volume_mute      :Change volume mute state on all connections <mute>
     change_volume_offset    :Change volume offset per connection <volume_offset
                              [volume_offset [...]]>
     change_microphone_mute  :Change microphone mute state on all connections <mute>
     change_microphone_gain  :Change microphone gain per connection <gain
                              [gain [...]]>


Before being able to perform any stream operation, the device must also perform the
:code:`bap discover` operation to discover the ASEs and PAC records. The :code:`bap init`
command also needs to be called.

When connected
--------------

Discovering CAS and CSIS on a device
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. code-block:: console

   uart:~$ cap_commander discover
   discovery completed with CSIS


Setting the volume on all connected devices
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. code-block:: console

   uart:~$ vcp_vol_ctlr discover
   VCP discover done with 1 VOCS and 1 AICS
   uart:~$ cap_commander change_volume 15
   uart:~$ cap_commander change_volume 15
   Setting volume to 15 on 2 connections
   VCP volume 15, mute 0
   VCP vol_set done
   VCP volume 15, mute 0
   VCP flags 0x01
   VCP vol_set done
   Volume change completed

Setting the volume offset on one or more devices
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The offsets are set by connection index, so connection index 0 gets the first offset,
and index 1 gets the second offset, etc.:

.. code-block:: console

   uart:~$ bt connect <device A>
   Connected: <device A>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ vcp_vol_ctlr discover
   VCP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ bt connect <device B>
   Connected: <device B>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ vcp_vol_ctlr discover
   VCP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ cap_commander change_volume_offset 10
   Setting volume offset on 1 connections
   VOCS inst 0x200140a4 offset 10
   Offset set for inst 0x200140a4
   Volume offset change completed
   uart:~$
   uart:~$ cap_commander change_volume_offset 10 15
   Setting volume offset on 2 connections
   Offset set for inst 0x200140a4
   VOCS inst 0x20014188 offset 15
   Offset set for inst 0x20014188
   Volume offset change completed

Setting the volume mute on all connected devices
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. code-block:: console

   uart:~$ bt connect <device A>
   Connected: <device A>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ vcp_vol_ctlr discover
   VCP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ bt connect <device B>
   Connected: <device B>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ vcp_vol_ctlr discover
   VCP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ cap_commander change_volume_mute 1
   Setting volume mute to 1 on 2 connections
   VCP volume 100, mute 1
   VCP mute done
   VCP volume 100, mute 1
   VCP mute done
   Volume mute change completed
   uart:~$ cap_commander change_volume_mute 0
   Setting volume mute to 0 on 2 connections
   VCP volume 100, mute 0
   VCP unmute done
   VCP volume 100, mute 0
   VCP unmute done
   Volume mute change completed

Setting the microphone mute on all connected devices
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. code-block:: console

   uart:~$ bt connect <device A>
   Connected: <device A>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ micp_mic_ctlr discover
   MICP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ bt connect <device B>
   Connected: <device B>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ micp_mic_ctlr discover
   MICP discover done with 1 VOCS and 1 AICS
   uart:~$
   uart:~$ cap_commander change_microphone_mute 1
   Setting microphone mute to 1 on 2 connections
   MICP microphone 100, mute 1
   MICP mute done
   MICP microphone 100, mute 1
   MICP mute done
   Microphone mute change completed
   uart:~$ cap_commander change_microphone_mute 0
   Setting microphone mute to 0 on 2 connections
   MICP microphone 100, mute 0
   MICP unmute done
   MICP microphone 100, mute 0
   MICP unmute done
   Microphone mute change completed

Setting the microphone gain on one or more devices
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The gains are set by connection index, so connection index 0 gets the first offset,
and index 1 gets the second offset, etc.:

.. code-block:: console

   uart:~$ bt connect <device A>
   Connected: <device A>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ micp_mic_ctlr discover
   MICP discover done with 1 AICS
   uart:~$
   uart:~$ bt connect <device B>
   Connected: <device B>
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ micp_mic_ctlr discover
   MICP discover done with 1 AICS
   uart:~$
   uart:~$ cap_commander change_microphone_gain 10
   Setting microphone gain on 1 connections
   AICS inst 0x200140a4 state gain 10, mute 0, mode 0
   Gain set for inst 0x200140a4
   Microphone gain change completed
   uart:~$
   uart:~$ cap_commander change_microphone_gain 10 15
   Setting microphone gain on 2 connections
   Gain set for inst 0x200140a4
   AICS inst 0x20014188 state gain 15, mute 0, mode 0
   Gain set for inst 0x20014188
   Microphone gain change completed

Starting a broadcast reception
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

.. code-block:: console

   uart:~$ bt connect <device A>
   Connected: <device A>
   uart:~$ bap_init
   uart:~$ cap_commander discover
   discovery completed with CSIS
   uart:~$ bap_broadcast_assistant discover
   BASS discover done with 1 recv states
   uart:~$ cap_commander broadcast_reception_start <device B> 0 4
   Starting broadcast reception on 1 connection(s)