STM32 Digital Camera Memory Interface 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: st,stm32-dcmi
.. _dtbinding_st_stm32_dcmi:

st,stm32-dcmi
#############

Vendor: :ref:`STMicroelectronics <dt_vendor_st>`

Description
***********



.. code-block:: none

   STMicroelectronics STM32 Digital Camera Memory Interface (DCMI).
   Example of node configuration at board level:

   &dcmi {
     status = "okay";
     sensor = <&ov2640>;
     pinctrl-0 = <&dcmi_hsync_pa4 &dcmi_pixclk_pa6 &dcmi_vsync_pb7
                 &dcmi_d0_pc6 &dcmi_d1_pc7 &dcmi_d2_pe0 &dcmi_d3_pe1
                 &dcmi_d4_pe4 &dcmi_d5_pd3 &dcmi_d6_pe5 &dcmi_d7_pe6>;
     pinctrl-names = "default";
     bus-width = <8>;
     hsync-active = <0>;
     vsync-active = <0>;
     pixelclk-active = <1>;
     capture-rate = <1>;
     dmas = <&dma1 0 75 (STM32_DMA_PERIPH_TO_MEMORY | STM32_DMA_PERIPH_NO_INC |
             STM32_DMA_MEM_INC | STM32_DMA_PERIPH_8BITS | STM32_DMA_MEM_32BITS |
             STM32_DMA_PRIORITY_HIGH) STM32_DMA_FIFO_1_4>;

     port {
       dcmi_ep_in: endpoint {
         remote-endpoint = <&ov2640_ep_out>;
       };
     };
   };

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``pinctrl-0``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the first state. Content is specific to the
                selected pin controller driver implementation.



         * - ``pinctrl-1``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the second state. See pinctrl-0.



         * - ``pinctrl-2``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the third state. See pinctrl-0.



         * - ``pinctrl-3``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fourth state. See pinctrl-0.



         * - ``pinctrl-4``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fifth state. See pinctrl-0.



         * - ``pinctrl-names``
           - ``string-array``
           - .. code-block:: none

                Names for the provided states. The number of names needs to match the
                number of states.



         * - ``sensor``
           - ``phandle``
           - .. code-block:: none

                phandle of connected sensor device


             This property is **required**.

         * - ``bus-width``
           - ``int``
           - .. code-block:: none

                Number of data lines actively used, valid for the parallel busses.



             This property is **required**.

             Default value: ``8``

             Legal values: ``8``, ``10``, ``12``, ``14``

         * - ``hsync-active``
           - ``int``
           - .. code-block:: none

                Polarity of horizontal synchronization (DCMI_HSYNC_Polarity).
                0 Horizontal synchronization active Low.
                1 Horizontal synchronization active High.

                For example, if DCMI_HSYNC_Polarity is programmed active high:
                When HSYNC is low, the data is valid.
                When HSYNC is high, the data is not valid (horizontal blanking).



             This property is **required**.

             Legal values: ``0``, ``1``

         * - ``vsync-active``
           - ``int``
           - .. code-block:: none

                Polarity of vertical synchronization (DCMI_VSYNC_Polarity).
                0 Vertical synchronization active Low.
                1 Vertical synchronization active High.

                For example, if DCMI_VSYNC_Polarity is programmed active high:
                When VSYNC is low, the data is valid.
                When VSYNC is high, the data is not valid (vertical blanking).



             This property is **required**.

             Legal values: ``0``, ``1``

         * - ``pixelclk-active``
           - ``int``
           - .. code-block:: none

                Polarity of pixel clock (DCMI_PIXCK_Polarity).
                0 Pixel clock active on Falling edge.
                1 Pixel clock active on Rising edge.



             This property is **required**.

             Legal values: ``0``, ``1``

         * - ``capture-rate``
           - ``int``
           - .. code-block:: none

                The DCMI can capture all frames or alternate frames. If it is not specified,
                the default is all frames.
                1 Capture all frames.
                2 Capture alternate frames.
                4 Capture one frame every 4 frames.



             Default value: ``1``

             Legal values: ``1``, ``2``, ``4``



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "st,stm32-dcmi" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                phandle of DMA controller. The DMA controller should be compatible with
                DMA channel specifier. Specifies a phandle reference to the dma controller,
                the channel number, the slot number, channel configuration and finally features.

                dmas = <&dma1 0 75 (STM32_DMA_PERIPH_TO_MEMORY | STM32_DMA_PERIPH_NO_INC |
                        STM32_DMA_MEM_INC | STM32_DMA_PERIPH_8BITS | STM32_DMA_MEM_32BITS |
                        STM32_DMA_PRIORITY_HIGH) STM32_DMA_FIFO_1_4>;



             This property is **required**.

         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().