STM32C0 Single-point Production-calibrated Temperature Sensor 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: st,stm32c0-temp-cal
.. _dtbinding_st_stm32c0_temp_cal:

st,stm32c0-temp-cal
###################

Vendor: :ref:`STMicroelectronics <dt_vendor_st>`

Description
***********



.. code-block:: none

   STM32 family TEMP node for production calibrated sensors like C0
   with a single calibration temperature.

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``friendly-name``
           - ``string``
           - .. code-block:: none

                Human readable string describing the sensor. It can be used to
                distinguish multiple instances of the same model (e.g., lid accelerometer
                vs. base accelerometer in a laptop) to a host operating system.

                This property is defined in the Generic Sensor Property Usages of the HID
                Usage Tables specification
                (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).



         * - ``ts-cal1-addr``
           - ``int``
           - .. code-block:: none

                address of parameter TS_CAL1


             This property is **required**.

         * - ``ts-cal1-temp``
           - ``int``
           - .. code-block:: none

                temperature at which temperature sensor has been
                calibrated in production for data into ts-cal1-addr



             This property is **required**.

         * - ``ts-cal-vrefanalog``
           - ``int``
           - .. code-block:: none

                Analog voltage reference (Vref+) voltage with which
                temperature sensor has been calibrated in production



             This property is **required**.

         * - ``ts-cal-resolution``
           - ``int``
           - .. code-block:: none

                Temperature calibration resolution with which the ts-cal1-temp and
                ts-cal2-temp are measured.
                For most stm32 series a native 12-bit ADC is embedded in the device,
                except for H7 on 16-bit and U5 on 14-bit



             Default value: ``12``

             Legal values: ``12``, ``14``, ``16``

         * - ``avgslope``
           - ``int``
           - .. code-block:: none

                Average slope of T-V chart (in uV/C) according to
                datasheet "Electrical characteristics/Operating conditions"
                STM32C0 Table 5.3.16 (min 2400 uV/C, max 2650, typ: 2530)



             Default value: ``2530``

         * - ``ntc``
           - ``boolean``
           - .. code-block:: none

                Negative Temperature Coefficient. True if STM32F0x0




   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "st,stm32c0-temp-cal" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


             This property is **required**.

         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().