NXP S32 Quadrature Decoder 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nxp,qdec-s32
.. _dtbinding_nxp_s32_qdec:

nxp,qdec-s32
############

Vendor: :ref:`NXP Semiconductors <dt_vendor_nxp>`

Description
***********



.. code-block:: none

   Quadrature Decoder driver which processes encoder signals to determine motor revs
   with the cooperation of S32 IP blocks- eMIOS, TRGMUX and LCU.
   The sensor qdec application can be used for testing this driver.
   The following example uses TRGMUX IN2 and IN3 to connect to LCU1 LC0 I0 and I1.
   LCU1 LC0 O2 and O3 connect to eMIOS0 CH6(Clockwise rotation) and
   CH7(Counter Clockwise rotation) via TRGMUX_INT_OUT37 and TRGMUX_INT_OUT38
   micro-ticks-per-rev is set as per vehicle gearbox reduction.
   lcu output filters are set to capture maximum speed sensitivity and avoid channel noise.

    qdec0 {
         compatible = "nxp,qdec-s32";
         pinctrl-0 = <&qdec_s32>;
         pinctrl-names = "default";
         micro-ticks-per-rev = <685440000>;
         status = "okay";
         trgmux = <&trgmux>;
         trgmux-io-config =
             <0 TRGMUX_IP_OUTPUT_EMIOS0_CH5_9_IPP_IND_CH6 TRGMUX_IP_INPUT_LCU1_LC0_OUT_I2>,
             <1 TRGMUX_IP_OUTPUT_EMIOS0_CH5_9_IPP_IND_CH7 TRGMUX_IP_INPUT_LCU1_LC0_OUT_I3>,
             <2 TRGMUX_IP_OUTPUT_LCU1_0_INP_I0            TRGMUX_IP_INPUT_SIUL2_IN2>,
             <3 TRGMUX_IP_OUTPUT_LCU1_0_INP_I1            TRGMUX_IP_INPUT_SIUL2_IN3>;
         lcu = <&lcu1>;
         lcu-input-idx = <1>;
             <LCU_IP_IN_0 LCU_IP_IN_1
             LCU_IP_IN_2 LCU_IP_IN_3>;
         lcu-mux-sel =
             <LCU_IP_MUX_SEL_LU_IN_0 LCU_IP_MUX_SEL_LU_IN_1
             LCU_IP_MUX_SEL_LU_OUT_0 LCU_IP_MUX_SEL_LU_OUT_1>;
         lcu-output-filter-config =
             /* LCU Out HW ID, Rise Filter, Fall Filter */
             <0 5 5>, /* LCU O0 */
             <1 5 5>, /* LCU O1 */
             <2 2 2>, /* LCU O2 */
             <3 2 2>; /* LCU O3 */
         emios = <&emios0>;
         emios-channels = <6 7>;
    };

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``pinctrl-0``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the first state. Content is specific to the
                selected pin controller driver implementation.



         * - ``pinctrl-1``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the second state. See pinctrl-0.



         * - ``pinctrl-2``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the third state. See pinctrl-0.



         * - ``pinctrl-3``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fourth state. See pinctrl-0.



         * - ``pinctrl-4``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fifth state. See pinctrl-0.



         * - ``pinctrl-names``
           - ``string-array``
           - .. code-block:: none

                Names for the provided states. The number of names needs to match the
                number of states.



         * - ``friendly-name``
           - ``string``
           - .. code-block:: none

                Human readable string describing the sensor. It can be used to
                distinguish multiple instances of the same model (e.g., lid accelerometer
                vs. base accelerometer in a laptop) to a host operating system.

                This property is defined in the Generic Sensor Property Usages of the HID
                Usage Tables specification
                (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).



         * - ``micro-ticks-per-rev``
           - ``int``
           - .. code-block:: none

                This is a number that is used to determine how many revolutions * 1000000
                were done based on the current counter's value.



         * - ``trgmux``
           - ``phandle``
           - .. code-block:: none

                phandle to the TRGMUX node.



         * - ``trgmux-io-config``
           - ``array``
           - .. code-block:: none

                This gives the logic triggers configuration of TRGMUX module.
                It contains 3 values for each of the 4 logic triggers used:
                  logic trigger number, output, input.
                Hence, it's length should be '12'.
                Ex:
                  trgmux-io-config =
                    <0 TRGMUX_IP_OUTPUT_EMIOS0_CH5_9_IPP_IND_CH6 TRGMUX_IP_INPUT_LCU1_LC0_OUT_I2>,
                    <1 TRGMUX_IP_OUTPUT_EMIOS0_CH5_9_IPP_IND_CH7 TRGMUX_IP_INPUT_LCU1_LC0_OUT_I3>,
                    <2 TRGMUX_IP_OUTPUT_LCU1_0_INP_I0            TRGMUX_IP_INPUT_SIUL2_IN2>,
                    <3 TRGMUX_IP_OUTPUT_LCU1_0_INP_I1            TRGMUX_IP_INPUT_SIUL2_IN3>;



         * - ``lcu``
           - ``phandle``
           - .. code-block:: none

                phandle to the LCU node.



         * - ``emios``
           - ``phandle``
           - .. code-block:: none

                phandle to the eMIOS node.



         * - ``lcu-output-filter-config``
           - ``array``
           - .. code-block:: none

                This array gives the configuration for each of the four outputs of LCU module.
                It contains the following for each output: hardware output id, rise filter and fall filter.
                The filters specify the delay in terms of CORE_CLK between the input and output line of LC.
                  We use this delay to generate short pulses at the rising and falling edges of input pulse.
                It's length should be '12' - 3 entries for each of the four LCU outputs.
                Ex: lcu-output-filter-config =
                  /* LCU Out HW ID, Rise Filter, Fall Filter */
                  <0 5 5>, /* LCU O0 */
                  <1 5 5>, /* LCU O1 */
                  <2 2 2>, /* LCU O2 */
                  <3 2 2>; /* LCU O3 */



         * - ``lcu-mux-sel``
           - ``array``
           - .. code-block:: none

                This array configures the sources of input to the LCU module by programming the muxsel.



         * - ``lcu-input-idx``
           - ``array``
           - .. code-block:: none

                This array configures the input indices to the LCU module which help to determine the
                Logic Cell number used inside an LCU instance.



         * - ``emios-channels``
           - ``array``
           - .. code-block:: none

                This is the array containing 2 emios channel TypeG numbers used by the qdec.





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nxp,qdec-s32" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().