Nordic nPM1300 PMIC Charger 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nordic,npm1300-charger
.. _dtbinding_nordic_npm1300_charger:

nordic,npm1300-charger
######################

Vendor: :ref:`Nordic Semiconductor <dt_vendor_nordic>`

Description
***********



.. code-block:: none

   NPM1300 PMIC Charger

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``friendly-name``
           - ``string``
           - .. code-block:: none

                Human readable string describing the sensor. It can be used to
                distinguish multiple instances of the same model (e.g., lid accelerometer
                vs. base accelerometer in a laptop) to a host operating system.

                This property is defined in the Generic Sensor Property Usages of the HID
                Usage Tables specification
                (https://usb.org/sites/default/files/hut1_3_0.pdf, section 22.5).



         * - ``term-microvolt``
           - ``int``
           - .. code-block:: none

                Charge termination voltage in uV.
                Available range is 3.5 V to 3.65 V and 4.0 V to 4.45 V in 50 mV steps.



             This property is **required**.

         * - ``term-warm-microvolt``
           - ``int``
           - .. code-block:: none

                Charge termination voltage when warm in uV.
                Available range is 3.5 V to 3.65 V and 4.0 V to 4.45 V in 50 mV steps.
                If omitted, the term-microvolt value will be used.



         * - ``current-microamp``
           - ``int``
           - .. code-block:: none

                Charge current in uA.
                Available range is 32 mA to 800 mA in 2mA steps.
                The value specified will be rounded down to the closest implemented value.



             This property is **required**.

         * - ``dischg-limit-microamp``
           - ``int``
           - .. code-block:: none

                Discharge current limit in uA.
                Available range is 270 mA to 1340 mA in 3.23 mA steps.
                The value specified will be rounded down to the closest implemented value.



             This property is **required**.

         * - ``vbus-limit-microamp``
           - ``int``
           - .. code-block:: none

                Vbus current limit in uA.
                Available values are 100 mA, or between 500 mA and 1500 mA in 100 mA steps.
                If omitted, the default value of 100 mA will be used.



         * - ``thermistor-ohms``
           - ``int``
           - .. code-block:: none

                Thermistor nominal resistance type in ohms.


             This property is **required**.

             Legal values: ``10000``, ``47000``, ``100000``

         * - ``thermistor-beta``
           - ``int``
           - .. code-block:: none

                Beta value of selected thermistor.


             This property is **required**.

         * - ``thermistor-cold-millidegrees``
           - ``int``
           - .. code-block:: none

                Thermistor cold threshold in milli-degrees


         * - ``thermistor-cool-millidegrees``
           - ``int``
           - .. code-block:: none

                Thermistor cool threshold in milli-degrees


         * - ``thermistor-warm-millidegrees``
           - ``int``
           - .. code-block:: none

                Thermistor warm threshold in milli-degrees


         * - ``thermistor-hot-millidegrees``
           - ``int``
           - .. code-block:: none

                Thermistor hot threshold in milli-degrees


         * - ``charging-enable``
           - ``boolean``
           - .. code-block:: none

                Enable charging.



         * - ``trickle-microvolt``
           - ``int``
           - .. code-block:: none

                Trickle voltage threshold in uV.
                Trickle charging is enabled below this value.
                If omitted the device default of 2.9V is used.



             Default value: ``2900000``

             Legal values: ``2900000``, ``2500000``

         * - ``term-current-percent``
           - ``int``
           - .. code-block:: none

                Termination current, as a percentage of current-microamp.
                Charge completes when the charge current falls below this value.
                If omitted the device default of 10% is used.



             Default value: ``10``

             Legal values: ``10``, ``20``

         * - ``vbatlow-charge-enable``
           - ``boolean``
           - .. code-block:: none

                Allow charging when below the vbatlow threshold.



         * - ``disable-recharge``
           - ``boolean``
           - .. code-block:: none

                Disable automatic recharge.



         * - ``dietemp-stop-millidegrees``
           - ``int``
           - .. code-block:: none

                Die temperature halt threshold in milli-degrees.
                When die temperature exceeds this threshold, charging will be inhibited.



         * - ``dietemp-resume-millidegrees``
           - ``int``
           - .. code-block:: none

                Die temperature resume threshold in milli-degrees.
                When die temperature falls below this threshold, charging will be permitted.





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nordic,npm1300-charger" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().