STM32F1 Pin Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: st,stm32f1-pinctrl
.. _dtbinding_st_stm32f1_pinctrl:

st,stm32f1-pinctrl
##################

Vendor: :ref:`STMicroelectronics <dt_vendor_st>`

Description
***********



.. code-block:: none

   STM32F1 Pin controller Node
   Based on pincfg-node.yaml binding.

   Note: `bias-disable` and `drive-push-pull` are default pin configurations.
          They will be applied in case no `bias-foo` or `driver-bar` properties
          are set.

Properties
**********

Top level properties
====================


These property descriptions apply to "st,stm32f1-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``swj-cfg``
           - ``string``
           - .. code-block:: none

                Configures number of pins assigned to the SWJ debug port.

                * full         - Full SWJ (JTAG-DP + SW-DP).
                * no-njtrst    - Full SWJ (JTAG-DP + SW-DP) but without NJTRST.
                                 Releases: PB4.
                * jtag-disable - JTAG-DP Disabled and SW-DP Enabled.
                                 Releases: PA15 PB3 PB4.
                * disable      - JTAG-DP Disabled and SW-DP Disabled.
                                 Releases: PA13 PA14 PA15 PB3 PB4.

                If absent, then Full SWJ (JTAG-DP + SW-DP) is used (reset state).



             Default value: ``full``

             Legal values: ``'full'``, ``'no-njtrst'``, ``'jtag-disable'``, ``'disable'``



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "st,stm32f1-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Child node properties
=====================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``bias-disable``
     - ``boolean``
     - .. code-block:: none

          disable any pin bias


   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-push-pull``
     - ``boolean``
     - .. code-block:: none

          drive actively high and low


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``output-low``
     - ``boolean``
     - .. code-block:: none

          set the pin to output mode with low level


   * - ``output-high``
     - ``boolean``
     - .. code-block:: none

          set the pin to output mode with high level


   * - ``pinmux``
     - ``int``
     - .. code-block:: none

          Adapted from
          https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml
          Integer array, represents gpio pin number and mux setting.
          These defines are calculated as: ((port * 16 + line) << 8) | (function << 6) | remap)
          With:
          - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
          - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
          - function: The configuration mode, can be:
          * 0 : Alternate function output
          * 1 : Input
          * 2 : Analog
          * 3 : GPIO output
          In case selected pin function is GPIO output, pin is statically configured as
          a plain output GPIO, which configuration can be set by adding 'ouptut-low' or
          'output-high' properties to the pinctrl configuration. Default is output-low.
          - remap: The pin remapping configuration. It allows to assign the pin
          function to a different peripheral. Remain configuration can be:
          * 0 : No remap
          * 1 : Partial remap 1
          * 2 : Partial remap 2
          * 3 : Partial remap 3
          * 4 : Full remap
          To simplify the usage, macro is available to generate "pinmux" field.
          This macro is available here:
            -include/zephyr/dt-bindings/pinctrl/stm32f1-pinctrl.h
          Some examples of macro usage:
             GPIO A9 set as alternate with no remap
          ... {
                   pinmux = <STM32F1_PINMUX('A', 9, ALTERNATE, REMAP_NO)>;
          };
             GPIO A9 set as alternate with full remap
          ... {
                   pinmux = <STM32F1_PINMUX('A', 9, ALTERNATE, REMAP_FULL)>;
          };
             GPIO A9 set as input
          ... {
                   pinmux = <STM32F1_PINMUX('A', 9, GPIO_IN, REMAP_NO)>;
          };
             GPIO A9 set as output-high
          ... {
                   pinmux = <STM32F1_PINMUX('A', 9, GPIO_OUT, REMAP_NO)>;
                   output-high;
          };



       This property is **required**.

   * - ``slew-rate``
     - ``string``
     - .. code-block:: none

          Pin output mode, maximum achievable speed. Only applies to
          output mode (alternate).



       Default value: ``max-speed-10mhz``

       Legal values: ``'max-speed-10mhz'``, ``'max-speed-2mhz'``, ``'max-speed-50mhz'``