NXP LPC IOCON Pin Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nxp,lpc-iocon-pinctrl
.. _dtbinding_nxp_lpc_iocon_pinctrl:

nxp,lpc-iocon-pinctrl
#####################

Vendor: :ref:`NXP Semiconductors <dt_vendor_nxp>`

Description
***********



.. code-block:: none

   LPC pinctrl node. This node defines pin configurations in pin groups, and has
   the 'pinctrl' node identifier in the SOC's devicetree. Each group within the
   pin configuration defines a peripheral's pin configuration. Each numbered
   subgroup represents pins with shared configuration for that peripheral. The
   'pinmux' property of each group selects the pins to be configured with these
   properties. For example, here is a configuration for FLEXCOMM0 pins:

   pinmux_flexcomm0_usart: pinmux_flexcomm0_usart {
     group0 {
       pinmux = <FC0_TXD_SCL_MISO_WS_PIO0_30>,
               <FC0_RXD_SDA_MOSI_DATA_PIO0_29>;
       slew-rate = "standard";
     };
   };

   If only the required properties are supplied, the ICON_PIO register will
   be assigned the following values:
   IOCON_FUNC=<pin mux selection>,
   IOCON_MODE=0,
   IOCON_SLEW=<slew-rate selection>,
   IOCON_INVERT=0,
   IOCON_DIGIMODE=1,
   IOCON_OD=0,

   Values for I2C type and analog type pins have the following defaults:
   IOCON_ASW=0
   IOCON_SSEL=0
   IOCON_FILTEROFF=1
   IOCON_ECS=0
   IOCON_EGP=1
   IOCON_I2CFILTER=1

   Note the inherited pinctrl properties defined below have the following effects:
   drive-open-drain: IOCON_OD=1
   bias-pull-up: IOCON_MODE=2
   bias-pull-down: IOCON_MODE=1
   drive-push-pull: IOCON_MODE=3

   Note: for the LPC11u6x, the following fields are also supported:
   IOCON_HYS- set by input-schmitt-enable
   IOCON_S_MODE- set by nxp,digital-filter
   IOCON_CLKDIV- set by nxp,filter-clock-div
   IOCON_FILTR- set by nxp,analog-filter

Properties
**********

Top level properties
====================


These property descriptions apply to "nxp,lpc-iocon-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nxp,lpc-iocon-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Grandchild node properties
==========================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-push-pull``
     - ``boolean``
     - .. code-block:: none

          drive actively high and low


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``input-schmitt-enable``
     - ``boolean``
     - .. code-block:: none

          enable schmitt-trigger mode


   * - ``pinmux``
     - ``array``
     - .. code-block:: none

          Pin mux selection for this group. See the SOC level pinctrl header
          file in NXP's HAL for a defined list of these options.



       This property is **required**.

   * - ``slew-rate``
     - ``string``
     - .. code-block:: none

          Pin output slew rate. Sets the SLEW field in the IOCON register.
          defaults to standard slew rate, due to this being the reset value of
          the field.
          0 SLEW_0- standard mode, output slew rate is slower
          1 SLEW_1- fast mode, output slew rate is faster



       Default value: ``standard``

       Legal values: ``'standard'``, ``'fast'``

   * - ``nxp,invert``
     - ``boolean``
     - .. code-block:: none

          Invert the pin input logic level



   * - ``nxp,analog-mode``
     - ``boolean``
     - .. code-block:: none

          Set the pin to analog mode. Sets DIGIMODE=0, and ASW=1. Only valid for
          analog type pins. Selects ASW0 on LPC55s3x family



   * - ``nxp,analog-alt-mode``
     - ``boolean``
     - .. code-block:: none

          Select the pin's alternate analog mode. Valid on LPC55s3x family SOCs
          when DIGIMODE=0. Only valid for analog type pins. Sets ASW1.



   * - ``power-source``
     - ``string``
     - .. code-block:: none

          Pin output power source. Only valid for I2C mode pins running in I2C
          mode.



       Legal values: ``'3v3'``, ``'1v8'``

   * - ``nxp,digital-filter``
     - ``boolean``
     - .. code-block:: none

          Digital input filter. Noise pulses below 10ms are filtered out.



   * - ``nxp,i2c-filter``
     - ``string``
     - .. code-block:: none

          I2C glitch filter speed. Only valid for I2C mode pins. Fast mode
          typically only required for High speed I2C.



       Legal values: ``'slow'``, ``'fast'``

   * - ``nxp,i2c-speed``
     - ``string``
     - .. code-block:: none

          I2C speed. Only valid for I2C mode pins. Fast mode should be used for
          fast mode plus I2C.



       Legal values: ``'slow'``, ``'fast'``

   * - ``nxp,i2c-pullup``
     - ``boolean``
     - .. code-block:: none

          Enable I2C pullup resistor. If not present, pin is open drain in I2C
          mode. Only valid for I2C mode pins in I2C mode



   * - ``nxp,i2c-mode``
     - ``boolean``
     - .. code-block:: none

          Enable I2C mode for a pin. If not present, pin is in GPIO mode. Only
          valid for I2C mode pins