Infineon CAT1 Pin Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: infineon,cat1-pinctrl
.. _dtbinding_infineon_cat1_pinctrl:

infineon,cat1-pinctrl
#####################

Vendor: :ref:`Infineon Technologies <dt_vendor_infineon>`

Description
***********



.. code-block:: none

   Infineon CAT1 Pinctrl container node

   This is a singleton node responsible for controlling the pin function selection
   and pin properties. For example, you can use this node to route
   UART0 RX to a particular port/pin and enable the pull-up resistor on that
   pin.

   The node has the 'pinctrl' node label set in SoC's devicetree,
   so you can modify it like this:

   &pinctrl {
       /* Your modifications go here */
   };

   Pin configuration can also specify the pin properties, for example the
   'bias-pull-up' property. Here is a list of the supported standard pin
   properties:
     * bias-high-impedance
     * bias-pull-up
     * bias-pull-down
     * drive-open-drain
     * drive-open-source
     * drive-push-pull   (strong)
     * input-enable      (input-buffer)

   Infineon CAT1 SoC's devicetree includes a set of pre-defined pin control
   Nodes, which can be found via MPN dtsi.
   For example, board cy8cproto_062_4343w uses the CY8C624ABZI_S2D44 part, so
   board dts (boards\arm\cy8cproto_062_4343w\cy8cproto_062_4343w.dts) includes MPN dts
   (infineon/psoc6/mpns/CY8C624ABZI_S2D44.dtsi).

   Each MPN dtsi includes package dtsi (../psoc6_xx/psoc6_xx.yyy-zzz.dtsi),
   For example, CY8C624ABZI_S2D44 includes "../psoc6_02/psoc6_02.124-bga.dtsi".

   An example of pre-defined pin control from package dtsi (e.g. psoc6_02.124-bga.dtsi):
   p3_0_scb2_uart_rx - RX pin UART2 (SCB2) which connected to port3.0

     /omit-if-no-ref/ p3_0_scb2_uart_rx: p3_0_scb2_uart_rx {
           pinmux = <DT_CAT1_PINMUX(3, 0, HSIOM_SEL_ACT_6)>;
     };

   Refer to psoc6_02.124-bga.dtsi for the list of all pre-defined pin control nodes.

   NOTE1 Pre-defined pin control nodes use macro DT_CAT1_PINMUX to
     initialize pinmux. DT_CAT1_PINMUX has the following input parameters
     DT_CAT1_PINMUX(port_number, pin_number, hsiom),
     hsiom is defined in the HSIOM_SEL_xxx macros in the
     zephyr\include\zephyr\dt-bindings\pinctrl\ifx_cat1-pinctrl.h file.

         You can use DT_CAT1_PINMUX to define your own pin control node:
           &pinctrl {
               my_uart_rx: my_uart_rx {
                   pinmux = <DT_CAT1_PINMUX(3, 0, HSIOM_SEL_ACT_6)>;
               };
           };

   NOTE2 Pre-defined pin control nodes do not have bias pin configuration.
     The bias configuration can be updated in board-pinctrl.dtsi
     &pinctrl {
       /* Configure pin control Bias mode for uart2 pins */
       p3_1_scb2_uart_tx {
         drive-push-pull;
       };

       p3_0_scb2_uart_rx {
         input-enable;
       };

       p3_2_scb2_uart_rts {
         drive-push-pull;
       };

       p3_3_scb2_uart_cts {
         input-enable;
       };
     };

   An example of the usage of pre-defined pin control nodes in your board's DTS file:

     &uart5 {
       pinctrl-0 = <&p5_1_scb5_uart_tx &p5_0_scb5_uart_rx>;
       pinctrl-names = "default";
     };

     /* Configure pin control bias mode for uart5 pins */
     &p5_1_scb5_uart_tx {
       drive-push-pull;
     };

     &p5_0_scb5_uart_rx {
       input-enable;
     };

Properties
**********

Top level properties
====================


These property descriptions apply to "infineon,cat1-pinctrl"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "infineon,cat1-pinctrl" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Child node properties
=====================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``bias-high-impedance``
     - ``boolean``
     - .. code-block:: none

          high impedance mode ("third-state", "floating")


   * - ``bias-pull-up``
     - ``boolean``
     - .. code-block:: none

          enable pull-up resistor


   * - ``bias-pull-down``
     - ``boolean``
     - .. code-block:: none

          enable pull-down resistor


   * - ``drive-push-pull``
     - ``boolean``
     - .. code-block:: none

          drive actively high and low


   * - ``drive-open-drain``
     - ``boolean``
     - .. code-block:: none

          drive with open drain (hardware AND)


   * - ``drive-open-source``
     - ``boolean``
     - .. code-block:: none

          drive with open source (hardware OR)


   * - ``input-enable``
     - ``boolean``
     - .. code-block:: none

          enable input on pin (e.g. enable an input buffer, no effect on output)



   * - ``pinmux``
     - ``int``
     - .. code-block:: none

          Encodes port/pin and alternate function.



       This property is **required**.