고정 Flash Partition 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: fixed-partitions
.. _dtbinding_fixed_partitions:

fixed-partitions
################

Vendor: :ref:`Generic or vendor-independent <dt_no_vendor>`

Description
***********



.. code-block:: none

   This binding is used to describe fixed partitions of a flash (or
   other nonvolatile storage) memory.

   Here is an example:

     &flash0 {
             partitions {
                     compatible = "fixed-partitions";
                     #address-cells = <1>;
                     #size-cells = <1>;

                     boot_partition: partition@0 {
                             label = "mcuboot";
                             reg = <0x00000000 0x0000C000>;
                     };
                     slot0_partition: partition@c000 {
                             label = "image-0";
                             reg = <0x0000C000 0x00076000>;
                     };
                     slot1_partition: partition@82000 {
                             label = "image-1";
                             reg = <0x00082000 0x00076000>;
                     };

                     /*
                      * The flash starting at 0x000f8000 and ending at
                      * 0x000fffff is reserved for use by the application.
                      */

                     /*
                      * Storage partition will be used by FCB/LittleFS/NVS
                      * if enabled.
                      */
                     storage_partition: partition@f8000 {
                             label = "storage";
                             reg = <0x000f8000 0x00008000>;
                     };
             };
     };

   Note that the usual name for this node is 'partitions'.
   The fixed-partitions node should be a child of the flash
   memory node. Note also that the flash memory node is usually
   different from the node representing the flash controller
   IP block.

   Above, slot0_partition's register address 0xc000 means that
   the partition begins at that offset from the parent flash
   memory flash0's base address. That is, partition addresses
   are relative; physical addresses must be calculated by adding
   the start address of flash0 in memory to each partition's
   reg address.

Properties
**********

Top level properties
====================


These property descriptions apply to "fixed-partitions"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "fixed-partitions" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                Number of cells required to represent a child node's
                reg property address. This must be large enough to
                represent the start offset of each partition.



         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                Number of cells required to represent a child node's
                reg property address. This must be large enough to
                represent the size of each partition in bytes.






Child node properties
=====================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``label``
     - ``string``
     - .. code-block:: none

          Human readable string describing the flash partition.



       See :ref:`dt-important-props` for more information.

   * - ``read-only``
     - ``boolean``
     - .. code-block:: none

          set this property if the partition is read-only


   * - ``reg``
     - ``array``
     - .. code-block:: none

          This should be in the format <OFFSET SIZE>, where OFFSET
          is the offset of the flash partition relative to the base
          address of the parent memory, and SIZE is the size of
          the partition in bytes.



       This property is **required**.

       See :ref:`dt-important-props` for more information.