Zephyr MSPI Emulation Controller 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: zephyr,mspi-emul-controller
.. _dtbinding_zephyr_mspi_emul_controller:

zephyr,mspi-emul-controller
###########################

Vendor: :ref:`Zephyr-specific binding <dt_vendor_zephyr>`

Description
***********

These nodes are "mspi" bus nodes.

.. code-block:: none

   Zephyr MSPI Emulation controller

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``clock-frequency``
           - ``int``
           - .. code-block:: none

                Clock frequency the MSPI peripheral is being driven at, in Hz.



         * - ``op-mode``
           - ``string``
           - .. code-block:: none

                Indicate MSPI controller or peripheral mode of the controller.
                The controller driver may use this during initialization.



             Legal values: ``'MSPI_CONTROLLER'``, ``'MSPI_PERIPHERAL'``

         * - ``duplex``
           - ``string``
           - .. code-block:: none

                Indicate MSPI Duplex mode, full or half.
                The controller driver may check this setting against its
                capabilities.



             Legal values: ``'MSPI_HALF_DUPLEX'``, ``'MSPI_FULL_DUPLEX'``

         * - ``dqs-support``
           - ``boolean``
           - .. code-block:: none

                Indicate whether the hardware supports DQS.
                The controller driver may check this setting against its
                capabilities.



         * - ``software-multiperipheral``
           - ``boolean``
           - .. code-block:: none

                Indicate whether the controller driver enables support for
                software managed multi peripheral feature.
                At the minimum, the controller driver should use it to allow
                or disallow calling mspi_dev_config with MSPI_DEVICE_CONFIG_NONE.



         * - ``ce-gpios``
           - ``phandle-array``
           - .. code-block:: none

                An array of chip select GPIOs to use. Each element
                in the array specifies a GPIO. The index in the array
                corresponds to the child node that the CE gpio controls.

                Example:

                  mspi@... {
                          ce-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>,
                                        <&gpio1 10 GPIO_ACTIVE_LOW>,
                                        ...;

                          mspi-device@0 {
                                  reg = <0>;
                                  ...
                          };
                          mspi-device@1 {
                                  reg = <1>;
                                  ...
                          };
                          ...
                  };

                The child node "mspi-device@0" specifies a mspi device with
                chip select controller gpio0, pin 23, and devicetree
                GPIO flags GPIO_ACTIVE_LOW. Similarly, "mspi-device@1" has CE GPIO
                controller gpio1, pin 10, and flags GPIO_ACTIVE_LOW. Additional
                devices can be configured in the same way.

                If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
                choice for a typical "CEn" pin. GPIO_ACTIVE_HIGH may be used if
                intervening hardware inverts the signal to the peripheral device or
                the line itself is active high.

                Regardless of whether the CE pin may need software control or MSPI
                controller has dedicated CE pin, this field should be defined to
                help manage multiple devices on the same MSPI controller.





   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "zephyr,mspi-emul-controller" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


             This property is **required**.

             Constant value: ``1``

         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


             This property is **required**.

         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().