Futaba SBUS Input 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: futaba,sbus
.. _dtbinding_futaba_sbus:

futaba,sbus (on uart bus)
#########################

Vendor: :ref:`Futaba Corporation <dt_vendor_futaba>`

Description
***********



.. code-block:: none

   SBUS input driver using
   This driver implements the SBUS protocol used on RC radio's
   to send out analogue joystick and switches output.
   SBUS is an single-wire inverted serial protocol so either you need to use
   the rx-invert feature of your serial driver or use an external signal inverter.
   The driver binds this to the Zephyr input system using INPUT_EV_CODES.

   The following examples defines a binding of 2 joysticks and a button using 5 channels.

   &lpuart6 {
     status = "okay";

     sbus {
         compatible = "futaba,sbus";
         right_stick_x {
             channel = <1>;
             type = <INPUT_EV_ABS>;
             zephyr,code = <INPUT_ABS_RX>;
         };
         right_stick_y {
             channel = <2>;
             type = <INPUT_EV_ABS>;
             zephyr,code = <INPUT_ABS_RY>;
         };
         left_stick_x {
             channel = <3>;
             type = <INPUT_EV_ABS>;
             zephyr,code = <INPUT_ABS_X>;
         };
         left_stick_y {
             channel = <4>;
             type = <INPUT_EV_ABS>;
             zephyr,code = <INPUT_ABS_Y>;
         };
         kill_switch {
             channel = <5>;
             type = <INPUT_EV_KEY>;
             zephyr,code = <INPUT_KEY_0>;
         };
     };
   };

Properties
**********

Top level properties
====================


These property descriptions apply to "futaba,sbus"
nodes themselves. This page also describes child node
properties in the following sections.

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      (None)

   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "futaba,sbus" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().






Child node properties
=====================

.. list-table::
   :widths: 1 1 4
   :header-rows: 1

   * - Name
     - Type
     - Details

   * - ``channel``
     - ``int``
     - .. code-block:: none

          SBUS input channel
          Valid range: 1 - 16



       This property is **required**.

   * - ``type``
     - ``int``
     - .. code-block:: none

          Input event types see INPUT_EV_CODES


       This property is **required**.

   * - ``zephyr,code``
     - ``int``
     - .. code-block:: none

          Code to emit.


       This property is **required**.