Infineon XMC4XXX USIC I2C 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: infineon,xmc4xxx-i2c
.. _dtbinding_infineon_xmc4xxx_i2c:

infineon,xmc4xxx-i2c
####################

Vendor: :ref:`Infineon Technologies <dt_vendor_infineon>`

Description
***********

These nodes are "i2c" bus nodes.

.. code-block:: none

   Infineon XMC4XXX I2C

   This driver configures the USIC as an I2C device.

   Example devicetree configuration with an adt7420 temperature sensor
   connected on the bus:

   &usic1ch1 {
       compatible = "infineon,xmc4xxx-i2c";
       status = "okay";

       pinctrl-0 = <&i2c_scl_p0_13_u1c1 &i2c_sda_p3_15_u1c1>;
       pinctrl-names = "default";
       scl-src = "DX1B";
       sda-src = "DX0A";
       interrupts = <94 1>;

       #address-cells = <1>;
       #size-cells = <0>;

       clock-frequency = <I2C_BITRATE_STANDARD>;
       adt7420@48 {
           compatible = "adi,adt7420";
           reg = <0x48>;
       };
   };

   The pinctrl nodes need to be configured as open-drain and
   hwctrl should be disabled:

   &i2c_scl_p0_13_u1c1 {
       drive-strength = "strong-sharp-edge";
       drive-open-drain;
       hwctrl = "disabled";
   };

   &i2c_sda_p3_15_u1c1 {
       drive-strength = "strong-soft-edge";
       drive-open-drain;
       hwctrl = "disabled";
   };

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``clock-frequency``
           - ``int``
           - .. code-block:: none

                Initial clock frequency in Hz


         * - ``sq-size``
           - ``int``
           - .. code-block:: none

                Size of the submission queue for blocking requests


             Default value: ``4``

         * - ``cq-size``
           - ``int``
           - .. code-block:: none

                Size of the completion queue for blocking requests


             Default value: ``4``

         * - ``pinctrl-0``
           - ``phandles``
           - .. code-block:: none

                PORT pin configuration for SCL, SDA signals.
                We expect that the phandles will reference pinctrl nodes. These
                nodes will have a nodelabel that matches the Infineon SoC Pinctrl
                defines and have following
                format: i2c_<signal>_p<port>_<pin>_<peripheral inst>

                Examples:
                  pinctrl-0 = <&i2c_scl_p5_2_u2c0 &i2c_sda_p5_0_u2c0>;

                The pins should set to open-drain and hwctrl should be disabled.

                &i2c_scl_p5_2_u2c0 {
                    drive-strength = "strong-sharp-edge";
                    drive-open-drain;
                    hwctrl = "disabled";
                };

                In the above example, the pin is both an input and output (as is
                required for I2C setup). It is internally connected to both DX0
                and DOUT0 of USIC2 channel 0. (See XMC4700/4800 reference manual
                page 18-110, Figure 18-50 for more details).
                This limits the number of pins that can be used for the I2C module.

                To get around this pin limitation, it is possible to use pins
                that do not have this internal connection, and instead connect the
                pins externally on the board.
                For example, for the SDA line on USIC2 channel 0, P3.8 may be used
                for DOUT0 and P6.5 for DX0. These type of pinctrl nodes will have
                labels:
                i2c_sda_dout0_p3_8_u2c0 and i2c_sda_dx0_p6_5_u2c0.
                The generalized format is: i2c_<signal>_<type>_p<port>_<pin>_<peripheral inst>

                An example for SCL and SDA signals on the xmc4700:
                pinctrl-0 = <&i2c_sda_dout0_p3_8_u2c0 &i2c_sda_dx0_p6_5_u2c0
                            &i2c_scl_dout1_p3_9_u2c0 &i2c_scl_p5_2_u2c0>;

                Externally P3.8 should be connected to P6.5; P3.9 should be connected
                to P5.2.

                Note that any pins that do not have dout0/dx0 or dout1/dx1 can have either
                function. Thus node i2c_scl_p5_0_u2c0 can be both dout1 and dx1.

                For the pin configurations, the output pins (dout0 and dout1) should be set
                to open-drain while the input pins (dx0 and dx1) should not include this setting.

                &i2c_sda_dout0_p3_8_u2c0 {
                    drive-strength = "strong-sharp-edge";
                    drive-open-drain;
                    hwctrl = "disabled";
                };

                &i2c_scl_dout1_p3_9_u2c0 {
                    drive-strength = "strong-sharp-edge";
                    drive-open-drain;
                    hwctrl = "disabled";
                };

                &i2c_sda_dx0_p6_5_u2c0 {   /* will require USIC setting sda-src = DX0D */
                    hwctrl = "disabled";
                };

                &i2c_scl_p5_2_u2c0 {  /* will require USIC scl-src = DX1A */
                    hwctrl = "disabled";
                };



             This property is **required**.

         * - ``pinctrl-1``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the second state. See pinctrl-0.



         * - ``pinctrl-2``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the third state. See pinctrl-0.



         * - ``pinctrl-3``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fourth state. See pinctrl-0.



         * - ``pinctrl-4``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fifth state. See pinctrl-0.



         * - ``pinctrl-names``
           - ``string-array``
           - .. code-block:: none

                Names for the provided states. The number of names needs to match the
                number of states.



             This property is **required**.

         * - ``scl-src``
           - ``string``
           - .. code-block:: none

                Connects the I2C clock line (USIC DX1 input) to a specific GPIO pin.
                The USIC DX1 input is a multiplexer which connects to different GPIO pins.
                Refer to the XMC4XXX reference manual for the GPIO pin/mux mappings.



             This property is **required**.

             Legal values: ``'DX1A'``, ``'DX1B'``, ``'DX1C'``, ``'DX1D'``, ``'DX1E'``, ``'DX1F'``, ``'DX1G'``

         * - ``sda-src``
           - ``string``
           - .. code-block:: none

                Connects the I2C data line (USIC DX0 input) to a specific GPIO pin.
                The USIC DX0 input is a multiplexer which connects to different GPIO pins.
                Refer to the XMC4XXX reference manual for the GPIO pin/mux mappings.



             This property is **required**.

             Legal values: ``'DX0A'``, ``'DX0B'``, ``'DX0C'``, ``'DX0D'``, ``'DX0E'``, ``'DX0F'``, ``'DX0G'``



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "infineon,xmc4xxx-i2c" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                IRQ number and priority to use for interrupt driven by I2C.
                Each USIC must use a certain interrupt range:
                USIC0 = [84, 89]
                USIC1 = [90, 95]
                USIC2 = [96, 101]



             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


             This property is **required**.

             Constant value: ``1``

         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


             This property is **required**.

         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().