Raspberry Pi Pico 40-pin Header 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: raspberrypi,pico-header
.. _dtbinding_raspberrypi_pico_header:

raspberrypi,pico-header
#######################

Vendor: :ref:`Raspberry Pi Foundation <dt_vendor_raspberrypi>`

Description
***********



.. code-block:: none

   GPIO pins exposed on Raspberry Pi Pico headers.

   The Raspberry Pi Pico layout provides 2 columns of 20 pins headers

   This binding provides a nexus mapping for the default 26 pins as depicted below:

       0  GPIO0/UART0_TX      VBUS            -
       1  GPIO1/UART0_RX      VSYS            -
       -  GND                 GND             -
       2  GPIO2               3V3_EN          -
       3  GPIO3               3V3_OUT         -
       4  GPIO4/I2C0_SDA      ADC_VREF        -
       5  GPIO5/I2C0_SCL      GPIO28/ADC2     28
       -  GND                 GND             -
       6  GPIO6               GPIO27/ADC1     27
       7  GPIO7               GPIO26/ADC0     26
       8  GPIO8               RUN             -
       9  GPIO9               GPIO22          22
       -  GND                 GND             -
       10 GPIO10              GPIO21          21
       11 GPIO11              GPIO20          20
       12 GPIO12              GPIO19/SPI0_TX  19
       13 GPIO13              GPIO18/SPI0_SCK 18
       -  GND                 GND             -
       14 GPIO14              GPIO17/SPI0_CSn 17
       15 GPIO15              GPIO16/SPI0_RX  16

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``gpio-map``
           - ``compound``
           - This property is **required**.

         * - ``gpio-map-mask``
           - ``compound``
           - 

         * - ``gpio-map-pass-thru``
           - ``compound``
           - 

         * - ``#gpio-cells``
           - ``int``
           - .. code-block:: none

                Number of items to expect in a GPIO specifier


             This property is **required**.



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "raspberrypi,pico-header" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().