Nuvoton NPCX FIU NOR flash 바인딩

:orphan:

.. raw:: html

    <!--
    FIXME: do not limit page width until content uses another representation
    format other than tables
    -->
    <style>.wy-nav-content { max-width: none; !important }</style>

.. dtcompatible:: nuvoton,npcx-fiu-nor
.. _dtbinding_nuvoton_npcx_fiu_nor:

nuvoton,npcx-fiu-nor (on qspi bus)
##################################

Vendor: :ref:`Nuvoton Technology Corporation <dt_vendor_nuvoton>`

Description
***********



.. code-block:: none

   The SPI NOR flash devices accessed by Nuvoton Flash Interface Unit (FIU).

   Representation of a SPI NOR flash on a qspi bus looks like:

     int_flash: w25q40@0 {
           compatible ="nuvoton,npcx-fiu-nor";
           size = <DT_SIZE_K(512 * 8)>;
           reg = <0>;

           qspi-flags = <NPCX_QSPI_SW_CS1>;
           mapped-addr = <0x64000000>;
           pinctrl-0 = <&int_flash_sl>;
           pinctrl-names = "default";
     };

Properties
**********

.. tabs::

   .. group-tab:: Node specific properties

      Properties not inherited from the base binding file.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``pinctrl-0``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the first state. Content is specific to the
                selected pin controller driver implementation.



         * - ``pinctrl-1``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the second state. See pinctrl-0.



         * - ``pinctrl-2``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the third state. See pinctrl-0.



         * - ``pinctrl-3``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fourth state. See pinctrl-0.



         * - ``pinctrl-4``
           - ``phandles``
           - .. code-block:: none

                Pin configuration/s for the fifth state. See pinctrl-0.



         * - ``pinctrl-names``
           - ``string-array``
           - .. code-block:: none

                Names for the provided states. The number of names needs to match the
                number of states.



         * - ``jedec-id``
           - ``uint8-array``
           - .. code-block:: none

                JEDEC ID as manufacturer ID, memory type, memory density


         * - ``size``
           - ``int``
           - .. code-block:: none

                flash capacity in bits


         * - ``sfdp-bfp``
           - ``uint8-array``
           - .. code-block:: none

                Contains the 32-bit words in little-endian byte order from the
                JESD216 Serial Flash Discoverable Parameters Basic Flash
                Parameters table.  This provides flash-specific configuration
                information in cases were runtime retrieval of SFDP data
                is not desired.



         * - ``quad-enable-requirements``
           - ``string``
           - .. code-block:: none

                Quad Enable Requirements value from JESD216 BFP DW15.

                Use NONE if the device detects 1-1-4 and 1-4-4 modes by the
                instruction.  Use S1B6 if QE is bit 6 of the first status register
                byte, and can be configured by reading then writing one byte with
                RDSR and WRSR.  For other fields see the specification.



             Legal values: ``'NONE'``, ``'S2B1v1'``, ``'S1B6'``, ``'S2B7'``, ``'S2B1v4'``, ``'S2B1v5'``, ``'S2B1v6'``

         * - ``enter-4byte-addr``
           - ``int``
           - .. code-block:: none

                Enter 4-Byte Addressing value from JESD216 BFP DW16

                This property is ignored if the device is configured to use SFDP data
                from the sfdp-bfp property (CONFIG_SPI_NOR_SFDP_DEVICETREE) or to read
                SFDP properties at runtime (CONFIG_SPI_NOR_SFDP_RUNTIME).

                For CONFIG_SPI_NOR_SFDP_MINIMAL this is the 8-bit value from bits 31:24
                of DW16 identifying ways a device can be placed into 4-byte addressing
                mode.  If provided as a non-zero value the driver assumes that 4-byte
                addressing is require to access the full address range, and
                automatically puts the device into 4-byte address mode when the device
                is initialized.



         * - ``page-size``
           - ``int``
           - .. code-block:: none

                Number of bytes in a page from JESD216 BFP DW11

                This property is only used in the CONFIG_SPI_NOR_SFDP_MINIMAL configuration.
                It is ignored if the device is configured to use SFDP data
                from the sfdp-bfp property (CONFIG_SPI_NOR_SFDP_DEVICETREE) or
                if the SFDP parameters are read from the device at
                runtime (CONFIG_SPI_NOR_SFDP_RUNTIME).

                The default value is 256 bytes if the value is not specified.



         * - ``requires-ulbpr``
           - ``boolean``
           - .. code-block:: none

                Indicates the device requires the ULBPR (0x98) command.

                Some flash chips such as the Microchip SST26VF series have a block
                protection register that initializes to write-protected.  Use this
                property to indicate that the BPR must be unlocked before write
                operations can proceed.



         * - ``has-dpd``
           - ``boolean``
           - .. code-block:: none

                Indicates the device supports the DPD (0xB9) command.

                Use this property to indicate the flash chip supports the Deep
                Power-Down mode that is entered by command 0xB9 to reduce power
                consumption below normal standby levels.  Use of this property
                implies that the RDPD (0xAB) Release from Deep Power Down command
                is also supported.  (On some chips this command functions as Read
                Electronic Signature; see t-enter-dpd).



         * - ``dpd-wakeup-sequence``
           - ``array``
           - .. code-block:: none

                Specifies wakeup durations for devices without RDPD.

                Some devices (Macronix MX25R in particular) wake from deep power
                down by a timed sequence of CSn toggles rather than the RDPD
                command.  This property specifies three durations measured in
                nanoseconds, in this order:
                (1) tDPDD (Delay Time for Release from Deep Power-Down Mode)
                (2) tCDRP (CSn Toggling Time before Release from Deep Power-Down Mode)
                (3) tRDP (Recovery Time for Release from Deep Power-Down Mode)

                Absence of this property indicates that the RDPD command should be
                used to wake the chip from Deep Power-Down mode.



         * - ``t-enter-dpd``
           - ``int``
           - .. code-block:: none

                Duration required to complete the DPD command.

                This provides the duration, in nanoseconds, that CSn must be
                remain deasserted after issuing DPD before the chip will enter
                deep power down.

                If not provided the driver does not enforce a delay.



         * - ``t-exit-dpd``
           - ``int``
           - .. code-block:: none

                Duration required to complete the RDPD command.

                This provides the duration, in nanoseconds, that CSn must be
                remain deasserted after issuing RDPD before the chip will exit
                deep power down and be ready to receive additional commands.

                If not provided the driver does not enforce a delay.



         * - ``has-lock``
           - ``int``
           - .. code-block:: none

                Bit mask of bits of the status register that should be cleared on
                startup.

                Some devices from certain vendors power-up with block protect bits
                set in the status register, which prevent any erase or program
                operation from working.  Devices that have this behavior need to
                clear those bits on startup.  However, other devices have
                non-volatile bits in the status register that should not be
                cleared.

                This value, when present, identifies bits in the status register
                that should be cleared when the device is initialized.



         * - ``mxicy,mx25r-power-mode``
           - ``string``
           - .. code-block:: none

                Select to configure flash to use ultra low power mode or high performance mode (L/H switch). The high performance mode has faster write and erase performance, but use more power than ultra low power mode.
                Only supported on Macronix MX25R Ultra Low Power series.


             Legal values: ``'low-power'``, ``'high-performance'``

         * - ``mapped-addr``
           - ``int``
           - .. code-block:: none

                Mapped memory address of direct read access for spi nor flash.


             This property is **required**.

         * - ``max-timeout``
           - ``int``
           - .. code-block:: none

                Typically, it equals to max timeout of chip erase in ms.


             Default value: ``10000``

         * - ``qspi-flags``
           - ``int``
           - .. code-block:: none

                The definitions for configuring the Quad-SPI peripherals.


             This property is **required**.

         * - ``rd-mode``
           - ``string``
           - .. code-block:: none

                Selects the SPI read access type of Direct Read Access. Usually, we choose
                Fast Read Dual I/O mode for better performance. If the nor spi flash does
                not support this mode, please set this property explicitly.



             Default value: ``NPCX_RD_MODE_FAST_DUAL``

             Legal values: ``'NPCX_RD_MODE_NORMAL'``, ``'NPCX_RD_MODE_FAST'``, ``'NPCX_RD_MODE_FAST_DUAL'``



   .. group-tab:: Deprecated node specific properties

      Deprecated properties not inherited from the base binding file.

      (None)

   .. group-tab:: Base properties

      Properties inherited from the base binding file, which defines
      common properties that may be set on many nodes. Not all of these
      may apply to the "nuvoton,npcx-fiu-nor" compatible.

      .. list-table::
         :widths: 1 1 4
         :header-rows: 1

         * - Name
           - Type
           - Details

         * - ``wakeup-source``
           - ``boolean``
           - .. code-block:: none

                Property to identify that a device can be used as wake up source.

                When this property is provided a specific flag is set into the
                device that tells the system that the device is capable of
                wake up the system.

                Wake up capable devices are disabled (interruptions will not wake up
                the system) by default but they can be enabled at runtime if necessary.



         * - ``power-domain``
           - ``phandle``
           - .. code-block:: none


                Power domain the device belongs to.

                The device will be notified when the power domain it belongs to is either
                suspended or resumed.



         * - ``zephyr,pm-device-runtime-auto``
           - ``boolean``
           - .. code-block:: none

                Automatically configure the device for runtime power management after the
                init function runs.



         * - ``zephyr,disabling-power-states``
           - ``phandles``
           - .. code-block:: none

                List of power states that will disable this device power.



         * - ``status``
           - ``string``
           - .. code-block:: none

                indicates the operational status of a device


             Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``

             See :ref:`dt-important-props` for more information.

         * - ``compatible``
           - ``string-array``
           - .. code-block:: none

                compatible strings


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg``
           - ``array``
           - .. code-block:: none

                register space


             This property is **required**.

             See :ref:`dt-important-props` for more information.

         * - ``reg-names``
           - ``string-array``
           - .. code-block:: none

                name of each register space


         * - ``interrupts``
           - ``array``
           - .. code-block:: none

                interrupts for device


             See :ref:`dt-important-props` for more information.

         * - ``interrupts-extended``
           - ``compound``
           - .. code-block:: none

                extended interrupt specifier for device


         * - ``interrupt-names``
           - ``string-array``
           - .. code-block:: none

                name of each interrupt


         * - ``interrupt-parent``
           - ``phandle``
           - .. code-block:: none

                phandle to interrupt controller node


         * - ``label``
           - ``string``
           - .. code-block:: none

                Human readable string describing the device (used as device_get_binding() argument)



             See :ref:`dt-important-props` for more information.

             This property is **deprecated**.

         * - ``clocks``
           - ``phandle-array``
           - .. code-block:: none

                Clock gate information


         * - ``clock-names``
           - ``string-array``
           - .. code-block:: none

                name of each clock


         * - ``#address-cells``
           - ``int``
           - .. code-block:: none

                number of address cells in reg property


         * - ``#size-cells``
           - ``int``
           - .. code-block:: none

                number of size cells in reg property


         * - ``dmas``
           - ``phandle-array``
           - .. code-block:: none

                DMA channels specifiers


         * - ``dma-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of DMA channel specifiers


         * - ``io-channels``
           - ``phandle-array``
           - .. code-block:: none

                IO channels specifiers


         * - ``io-channel-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of IO channel specifiers


         * - ``mboxes``
           - ``phandle-array``
           - .. code-block:: none

                mailbox / IPM channels specifiers


         * - ``mbox-names``
           - ``string-array``
           - .. code-block:: none

                Provided names of mailbox / IPM channel specifiers


         * - ``zephyr,deferred-init``
           - ``boolean``
           - .. code-block:: none

                Do not initialize device automatically on boot. Device should be manually
                initialized using device_init().