boards/shields/semtech_sx1272mb2das/doc/index.html · boards/shields/semtech_sx1272mb2das/doc/index.rst 공식 원문 ↗

Zephyr 3.7.0 · Shields · LoRa · SX1272

Semtech SX1272MB2DAS LoRa Shield

SX1272 LoRa transceiver의 네 interrupt와 SPI bus를 Arduino connector에 배치합니다.

Official pathboards/shields/semtech_sx1272mb2das/doc/index.html
Source fileboards/shields/semtech_sx1272mb2das/doc/index.rst
Source versionZephyr 3.7.0
TranslationFull · reviewed

본문 기준: Zephyr 3.7.0 LTS3 · 이후 유지보수 패치는 별도입니다.

Part 1

요약·해설

9개 pin mapping, connector에 없는 DIO4/5, host board의 SPI·GPIO node alias 조건을 설명합니다.

Radio

SX1272

DIO

0–3 exposed

Bus

SPI

Build

nucleo_f429zi

Part 2

접을 수 있는 영어 원문 전체

영어 원문 전체 펼치기
원문 SHA-256 98BB077CAAA3B210BA423D2513E2AEA6392CA2AF59A204268B7BEA18679F500B
.. _semtech_sx1272mb2das:

Semtech SX1272MB2DAS LoRa Shield
################################

Overview
********

The Semtech SX1272MB2DAS LoRa shield is an Arduino
compatible shield based on the SX1272 LoRa transceiver
from Semtech.

More information about the shield can be found
at the `mbed SX1272MB2xAS website`_.

Pins Assignment of the Semtech SX1272MB2DAS LoRa Shield
=======================================================

+-----------------------+-----------------+
| Shield Connector Pin  | Function        |
+=======================+=================+
| A0                    | SX1272 RESET    |
+-----------------------+-----------------+
| D2                    | SX1272 DIO0     |
+-----------------------+-----------------+
| D3                    | SX1272 DIO1     |
+-----------------------+-----------------+
| D4                    | SX1272 DIO2     |
+-----------------------+-----------------+
| D5                    | SX1272 DIO3     |
+-----------------------+-----------------+
| D10                   | SX1272 SPI NSS  |
+-----------------------+-----------------+
| D11                   | SX1272 SPI MOSI |
+-----------------------+-----------------+
| D12                   | SX1272 SPI MISO |
+-----------------------+-----------------+
| D13                   | SX1272 SPI SCK  |
+-----------------------+-----------------+

The SX1272 signals DIO4 and DIO5 are not available at the shield connector.

Requirements
************

This shield can only be used with a board which provides a configuration
for Arduino connectors and defines node aliases for SPI and GPIO interfaces
(see :ref:`shields` for more details).

Programming
***********

Set ``--shield semtech_sx1272mb2das`` when you invoke ``west build``. For
example:

.. zephyr-app-commands::
   :zephyr-app: samples/subsys/lorawan/class_a
   :board: nucleo_f429zi
   :shield: semtech_sx1272mb2das
   :goals: build

References
**********

.. target-notes::

.. _mbed SX1272MB2xAS website:
   https://os.mbed.com/components/SX1272MB2xAS/

Part 3

한국어 전문 번역

개요

Semtech SX1272MB2DAS LoRa shield는 Semtech SX1272 LoRa transceiver 기반의 Arduino-compatible shield입니다.

자세한 정보는 mbed SX1272MB2xAS website에서 확인할 수 있습니다.

Semtech SX1272MB2DAS LoRa shield 핀 배치

Shield connector pinFunction
A0SX1272 RESET
D2SX1272 DIO0
D3SX1272 DIO1
D4SX1272 DIO2
D5SX1272 DIO3
D10SX1272 SPI NSS
D11SX1272 SPI MOSI
D12SX1272 SPI MISO
D13SX1272 SPI SCK

SX1272의 DIO4와 DIO5 signal은 shield connector에서 사용할 수 없습니다.

요구 사항

이 shield는 Arduino connector 구성을 제공하고 SPI 및 GPIO interface용 node alias를 정의한 board에서만 사용할 수 있습니다.

프로그래밍

west build를 호출할 때 --shield semtech_sx1272mb2das를 지정합니다. 예:

west build -b nucleo_f429zi   --shield semtech_sx1272mb2das   samples/subsys/lorawan/class_a

참고 자료

Source

출처

영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.