boards/shields/mikroe_eth_click/doc/index.html · boards/shields/mikroe_eth_click/doc/index.rst 공식 원문 ↗

Zephyr 3.7.0 · Shields · mikroBUS · Ethernet

MikroElektronika ETH Click

MAC·PHY와 8KB RAM을 내장한 ENC28J60 10BASE-T controller를 SPI로 연결합니다.

Official pathboards/shields/mikroe_eth_click/doc/index.html
Source fileboards/shields/mikroe_eth_click/doc/index.rst
Source versionZephyr 3.7.0
TranslationFull · reviewed

본문 기준: Zephyr 3.7.0 LTS3 · 이후 유지보수 패치는 별도입니다.

Part 1

요약·해설

Reset·SPI·interrupt 여섯 signal, Mikro-BUS SPI/GPIO 요구 사항과 원문의 SDI=MISO 표기를 설명합니다.

Controller

ENC28J60

Ethernet

10BASE-T

Buffer

8KB RAM

Bus

SPI

Part 2

접을 수 있는 영어 원문 전체

영어 원문 전체 펼치기
원문 SHA-256 A290E2E8CAC87DB0C672C73F78206DE47F04FFC85F47130FE8782C6431AD10CD 
.. _mikroe_eth_click:

MikroElektronika ETH Click
##########################

Overview
********

ETH Click is an accessory board in mikroBus™ form factor. It features `ENC28J60`_,
a 28-pin, 10BASE-T stand alone Ethernet Controller with an on-board MAC & PHY,
8K Bytes of Buffer RAM and SPI serial interface.
More information at `Eth Click Shield website`_.

Pins Assignment of the Eth Click Shield
=======================================

+-----------------------+---------------------------------------------+
| Shield Connector Pin  | Function                                    |
+=======================+=============================================+
| RST#                  | Ethernet Controller's Reset                 |
+-----------------------+---------------------------------------------+
| CS#                   | SPI's Chip Select                           |
+-----------------------+---------------------------------------------+
| SCK                   | SPI's ClocK                                 |
+-----------------------+---------------------------------------------+
| SDO                   | SPI's Slave Data Output  (MISO)             |
+-----------------------+---------------------------------------------+
| SDI                   | SPI's Slave Data Input   (MISO)             |
+-----------------------+---------------------------------------------+
| INT                   | Ethernet Controller's Interrupt Output      |
+-----------------------+---------------------------------------------+


Requirements
************

This shield can only be used with a board which provides a configuration
for Mikro-BUS connectors and defines node aliases for SPI and GPIO interfaces
(see :ref:`shields` for more details).

Programming
***********

Set ``--shield mikroe_eth_click`` when you invoke ``west build``. For example:

.. zephyr-app-commands::
   :zephyr-app: samples/net/dhcpv4_client
   :board: lpcxpresso55s69
   :shield: mikroe_eth_click
   :goals: build

References
**********

.. target-notes::

.. _Eth Click Shield website:
   https://www.mikroe.com/eth-click

.. _ENC28J60:
   https://www.microchip.com/wwwproducts/en/en022889

Part 3

한국어 전문 번역

개요

ETH Click은 mikroBUS form factor의 accessory board입니다. 28-pin ENC28J60은 on-board MAC과 PHY, 8KB buffer RAM, SPI serial interface를 갖춘 stand-alone 10BASE-T Ethernet controller입니다.

Pin assignment

Shield connector pinFunction
RST#Ethernet controller reset
CS#SPI chip select
SCKSPI clock
SDOSPI slave data output (MISO)
SDISPI slave data input (원문 표기: MISO)
INTEthernet controller interrupt output

요구 사항

Mikro-BUS connector configuration과 SPI·GPIO interface용 node alias를 제공하는 board에서만 사용할 수 있습니다.

프로그래밍

west build를 실행할 때 --shield mikroe_eth_click을 지정합니다.

west build -b lpcxpresso55s69   --shield mikroe_eth_click   samples/net/dhcpv4_client

참고 자료

Source

출처

영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.