Part 1
요약·해설
GD32F470I-EVAL은 3MiB Flash와 external NOR·SDRAM, 4.3-inch LCD, camera와 Ethernet을 제공합니다.

Cortex-M4F · 240MHz
140
camera · LCD · Ethernet
Part 2
접을 수 있는 영어 원문 전체
영어 원문 전체 펼치기
FE2876294434830666CFCDB3ACEA42293045F767BB056AA61032DAD3EE9521CC
.. _gd32f470i_eval:
GigaDevice GD32F470I-EVAL
#########################
Overview
********
The GD32F470I-EVAL board is a hardware platform that enables prototyping
on GD32F470IK Cortex-M4F Stretch Performance MCU.
The GD32F470IK features a single-core ARM Cortex-M4F MCU which can run up
to 240 MHz with flash accesses zero wait states, 3072kiB of Flash, 256kiB of
SRAM and 140 GPIOs.
.. image:: ../../../../../../../boards/gd/gd32f470i_eval/doc/img/gd32f470i_eval.jpg
:align: center
:alt: gd32f470i_eval
Hardware
********
- GD32F470IKH6 MCU
- 2Kb EEPROM
- 16Mbit SPI and QSPI NOR Flash
- 256Mbit SDRAM
- 3 x User LEDs
- 3 x User Push buttons
- 1 x USART (RS-232 at J1 connector)
- 1 x POT connected to an ADC input
- Headphone interface
- Micro SD Card Interface
- USB FS connector
- USB HS connector
- 1 x CAN
- Ethernet Interface
- 4.3" LCD (480x272)
- OV2640 Digital Camera
- GD-Link on board programmer
- J-Link/JTAG connector
For more information about the GD32F470 SoC and GD32F470I-EVAL board:
- `GigaDevice Cortex-M4F Stretch Performance SoC Website`_
- `GD32F470IKH6 Specifications`_
- `GD32F470xx Datasheet`_
- `GD32F4xx User Manual`_
Supported Features
==================
The board configuration supports the following hardware features:
.. list-table::
:header-rows: 1
* - Peripheral
- Kconfig option
- Devicetree compatible
* - EXTI
- :kconfig:option:`CONFIG_GD32_EXTI`
- :dtcompatible:`gd,gd32-exti`
* - GPIO
- :kconfig:option:`CONFIG_GPIO`
- :dtcompatible:`gd,gd32-gpio`
* - NVIC
- N/A
- :dtcompatible:`arm,v7m-nvic`
* - PWM
- :kconfig:option:`CONFIG_PWM`
- :dtcompatible:`gd,gd32-pwm`
* - SYSTICK
- N/A
- N/A
* - USART
- :kconfig:option:`CONFIG_SERIAL`
- :dtcompatible:`gd,gd32-usart`
* - DAC
- :kconfig:option:`CONFIG_DAC`
- :dtcompatible:`gd,gd32-dac`
* - I2C
- :kconfig:option:`CONFIG_I2C`
- :dtcompatible:`gd,gd32-i2c`
* - EEPROM
- :kconfig:option:`CONFIG_EEPROM`
- :dtcompatible:`atmel,at24`
* - SPI
- :kconfig:option:`CONFIG_SPI`
- :dtcompatible:`gd,gd32-spi`
Serial Port
===========
The GD32F470I-EVAL board has one serial communication port. The default port
is USART0 with TX connected at PA9 and RX at PA10.
Programming and Debugging
*************************
Before programming your board make sure to configure boot and serial jumpers
as follows:
- J2/3: Select 2-3 for both (boot from user memory)
- J5: Select 1-2 position (labeled as ``USART0``)
Using GD-Link
=============
The GD32F470I-EVAL includes an onboard programmer/debugger (GD-Link) which
allows flash programming and debugging over USB. There is also a JTAG header
(J1) which can be used with tools like Segger J-Link.
#. Build the Zephyr kernel and the :ref:`hello_world` sample application:
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: gd32f470i_eval
:goals: build
:compact:
#. Run your favorite terminal program to listen for output. On Linux the
terminal should be something like ``/dev/ttyUSB0``. For example:
.. code-block:: console
minicom -D /dev/ttyUSB0 -o
The -o option tells minicom not to send the modem initialization
string. Connection should be configured as follows:
- Speed: 115200
- Data: 8 bits
- Parity: None
- Stop bits: 1
#. To flash an image:
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: gd32f470i_eval
:goals: flash
:compact:
You should see "Hello World! gd32f470i_eval" in your terminal.
#. To debug an image:
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: gd32f470i_eval
:goals: debug
:compact:
.. _GigaDevice Cortex-M4F Stretch Performance SoC Website:
https://www.gigadevice.com/products/microcontrollers/gd32/arm-cortex-m4/stretch-performance-line/gd32f470-series/
.. _GD32F470IKH6 Specifications:
https://www.gigadevice.com/microcontroller/gd32f470ikh6/
.. _GD32F470xx Datasheet:
https://gd32mcu.com/data/documents/datasheet/GD32F470xx_Datasheet_Rev1.3.pdf
.. _GD32F4xx User Manual:
https://gd32mcu.com/data/documents/userManual/GD32F4xx_User_Manual_Rev2.7.pdf
Part 3
한국어 전문 번역
개요
GD32F470I-EVAL board는 GD32F470IK Cortex-M4F stretch-performance MCU로 prototype을 제작할 수 있는 hardware platform입니다.
GD32F470IK에는 최대 240MHz로 동작하는 single-core ARM Cortex-M4F MCU가 들어 있습니다. Flash 접근은 zero wait state이며 3072KiB Flash, 256KiB SRAM, GPIO 140개를 제공합니다.

Hardware
- GD32F470IKH6 MCU
- 2Kb EEPROM
- 16Mbit SPI/QSPI NOR Flash
- 256Mbit SDRAM
- User LED 3개
- User push button 3개
- USART 1개(J1 connector의 RS-232)
- ADC input에 연결된 potentiometer 1개
- Headphone interface
- Micro SD card interface
- USB FS connector
- USB HS connector
- CAN 1개
- Ethernet interface
- 4.3-inch LCD(480x272)
- OV2640 digital camera
- Onboard GD-Link programmer
- J-Link/JTAG connector
GD32F470 SoC와 board의 자세한 내용은 product page, chip specification, datasheet와 user manual에서 확인할 수 있습니다.
지원 기능
Board configuration은 다음 hardware 기능을 지원합니다.
| 주변장치 | Kconfig option | Devicetree compatible |
|---|---|---|
| EXTI | CONFIG_GD32_EXTI | gd,gd32-exti |
| GPIO | CONFIG_GPIO | gd,gd32-gpio |
| NVIC | N/A | arm,v7m-nvic |
| PWM | CONFIG_PWM | gd,gd32-pwm |
| SYSTICK | N/A | N/A |
| USART | CONFIG_SERIAL | gd,gd32-usart |
| DAC | CONFIG_DAC | gd,gd32-dac |
| I2C | CONFIG_I2C | gd,gd32-i2c |
| EEPROM | CONFIG_EEPROM | atmel,at24 |
| SPI | CONFIG_SPI | gd,gd32-spi |
Serial port
GD32F470I-EVAL에는 serial communication port가 1개 있습니다. Default port는 TX가 PA9, RX가 PA10에 연결된 USART0입니다.
Programming과 Debugging
Programming 전에 J2/3을 모두 2-3으로 선택해 user memory에서 boot하고, J5를 USART0이라고 표시된 1-2 위치로 설정합니다.
GD-Link 사용
Onboard GD-Link는 USB flash programming과 debugging을 지원합니다. J1 JTAG header에는 Segger J-Link 같은 tool도 연결할 수 있습니다.
- Zephyr kernel과
hello_worldsample을 build합니다.west build -b gd32f470i_eval samples/hello_world - Linux의
/dev/ttyUSB0같은 terminal에서 output을 받습니다.minicom -D /dev/ttyUSB0 -o-o는 modem initialization string을 보내지 않습니다. Connection 설정은 다음과 같습니다.- Speed: 115200
- Data: 8 bits
- Parity: None
- Stop bits: 1
- Image를 flash합니다.
west flashHello World! gd32f470i_eval가 terminal에 표시되어야 합니다. - Image를 debug합니다.
west debug
참고 자료
Source
출처
영어 원문에는 문단, 문서 지시문, 표, 코드, 코드 심벌, 경로를 그대로 보존했습니다.